Search results

Are the antennas that come with the goggles just basic or are they pretty good? I have seen some CP antennas that have the top covered, are they better? Are there any decent upgrades to these antennas that will improve my FPV experience? Does this also pertain to the antenna on the quad?

I flew for 7 minutes just goofing around and had a blast. I really need a larger field but for now this has to do. After the flight, I checked the capacity and the pack was down to 38%. So I think I'll limit my flights from now on to 6 minutes so I don't over discharge. The battery I used is the...

I have been working on this for a couple weeks on and off now. I finally figured out how I wanted things situated inside. I have my two main charging boards installed permanent and will have a storage compartment in the lid of the case later for other things such as pigtail leads, 1s paraboards...

I need help setting up my fpv system. I want to be able to see all the information on the screen on my goggles. I turn on my Tx and quad then plug in my goggles. All I get is a screen with some info but when I arm the motors, that info goes away and I get a blank screen.

Does it really matter which side you attach the patch antenna to your FPV goggles? I see most put it on the right.

Saw these at best buy today. Wayyy over my budget.

I can't find any online...

Which would you choose for your quad and why? I have read to use blheli as it was developed for quads.

I need to reverse 2 of my motors on my quad to get it to fly. I can't figure out how to do this. @Tony How did you do this on yours? I sure hope this doesn't turn out to be a nightmare like what we dealt with last night.

I bought a couple more batteries today in lieu of the rapid increase in price of the Tattu batteries I had initially purchased. When I bought my first ones they were $27 each. After 2 weeks, they are now $37. I found this other battery that looks like it may be a pretty good one so I bought 2 of...

Why does this thing do this when on storage mode? Switching from STO to CHG...

I looked at the clearance rack when checking out and got a Dremel MM40, tool only display model for $25. I can get the blades at harbor freight. This thing is normally $100 or so. Multi Max Mm40 - dremel.com

Thought I'd share this. I used a 3 AS A battery holder with switch to power the unit. Double sided tape to secure it to the holder.

I got one screw out and it is a right hand thread. Is the other one a left hand? It's very tight and I don't want to break it.

I got two new servos from amazon. They are to replace the broken ones in my 270 CFX. When they arrived, there is no top on them. Do they all come like that? I guess I'll need to use my old ones. Should I apply any type of grease to the gears?

I need to know how to mod this power supply for use on my charger. @Tony I see you have a video on you tube that shows modding a 600w PSU. Are those the same as the 700w?

I bought a pitch gauge from amazon and the stupid thing didn't work. I tried different batteries in it and nothing. It was a YooCoo or something. I guess all of them are about the same right? What's a dependable brand?

This is basically directed toward @Tony. I'm not sure what frame you plan to use for the stack-x but I'm wondering how you will mount your camera? The frames I have are too wide to use the camera mount that came with them. Is there an aftermarket mount that will work with this one?

I want to verify the pinout of this DSMX satellite from Lemon Rx. When looking at it from the top and the connector is on the bottom, the pinout is, from left to right, 3.3v, gnd., signal. Correct???

How should the motors be arranged on a quad? Does it really matter? Should the #1 motor be on the top right, top left? Should it be CCW, CW? Is there a science behind it? Motors are listed as if looking down on the quad with the front being at the top.