Search results

I need to try to build a paraboard for these batteries. Not sure what the connector is. Battery is 600mAh 25C LiPo.

This is pulp fiction!

Started building the FT Mini Scout tonight. I got the templates cut out but will wait till tomorrow to place them on the foam board. This plane takes a single sheet. Not pictured are the 4 circles for the wheels. I opted not to use them as I have cut them with my Olfa circle cutter.

So..its ok to use it in a dry location that's also wet? No, that's not right...it must be ok to use it in wet locations that are dry. Ah, I give up...

Anyone here own this gun? I have seen videos talking about how it starts oozing out where the stick enters the heating chamber. I have found a good deal on one but if it's junk then I'll pass.

I wonder if there could be a way to add a seller rating in the profile section. It would also be cool to display it below their avatar.

I have been looking for a cheap source for 5g servos. I can get ten 9g servos for about $18. The 5g ones seem to be much higher in price per servo. Where have you found the best deal on these?

Saw this online and had to build one. It's built from a single sheet of foam board. The plans are available free online and are in full size and tiled format. With a little patience you can have this done in about 6 hours, maybe less. It uses 2 9g servos and various motor/esc/battery setups. I'm...

I want to try to build one of those planes that has a flat cross section. The wings are flat and the fuselage is flat. When viewed from the front, it looks like a + sign. I want something small around 30" wing span. Anyone got any good plans to share? Links? Thanks.

I'm getting this error again. I forgot what fixed it last time. This happens on PC and mobile versions of the site.

I have some of these screws that came with my Thunder Tiger Super Decathlon which I purchased around 2005. They look simply like a flanged head phillips sheet metal screw. I wasn't sure if they had a specific name in the RC hobby. I want to buy some of these and need to know where a cheap source...

Once in a while I get coupons from harbor freight that I think would benefit others. Here are a couple to start. I will use this thread to post new coupons as I get them. I always tell the coupon code located below the barcode to the cashier. I haven't given them a physical coupon in a couple...

Where is the cheapest place you guys have found these? Is one type better than the other? I had some red ones but they were not as good as I had thought. They broke easily as they were almost rotten. I can't fly my RCH Trainer until I get some. What is a good general size to get?

I notice that on the older trucks the servo has a white round servo saver which is mounted directly on it. My truck, the 3.3 version has a spring loaded mechanism underneath. Is this an upgraded servo saver?

What's the difference with all the eachine cameras? There are 5 variants from TX01 to 05. One has a straight antenna which is noticable but which is the better one? I'm guessing they all work the same???

Anyone used this camera? AIO 5.8G 40CH 25MW VTX 800TVL 1/3 Cmos FPV Camera for Eachine E010C E010S Spare Parts Sale - Banggood Mobile

What is the proper adjustment for the pivot ball caps? These are the caps that cover the pivot balls which screw into the A arms. You can see them through the wheel spokes.

How long should I wait until driving my truck? Or is there a certain temp?

I have been noticing this wheel has some play in it. I took the hub apart last night but couldn't find anything wrong. The bearings are as smooth as silk. There is no noticeable wear on the shaft. For a truck this old there shouldn't be any wobble in it. When I roll it on the ground there is...

I want to build a stand for my truck. I can simply put it on a 4x4 block but I want something that is good looking too. What have you guys done for a home built stand? Photos are a +.