Search results

I have firmware on my stack-x that came from the Banggood website. My quad flies pretty well. If I change firmware, will I have to setup all the settings again?

I found this on amazon. I thought I'd ask about it due to the claim of 13dbi. I wonder if the claim is accurate...???

I have a Linksys E4200 router. I live in an older house which was built with nothing but brick (father in law was a brick mason). It's very hard for wireless signals to get through the walls into my living room. I want to know what range extenders are decent. I don't want to spend a lot on one...

So I got this broken safety light from work. It has all kinds of jumbo LEDs inside that flash in a safety pattern. Somehow somebody took out some serious fury on it. The outer case was ransacked. The PCB was demolished. But the 1s 1300mAh lipo was in tact. I salvaged it and brought it home. When...

I'm trying to find info on this camera. I need to know what the dip switch settings are for the channels. I thought they were TX02 but that camera has a 7 segment display. It looks as if it has MC32 but that turns up nothing. @D.O.G. do you remember the model of this camera? It's one I got...

@Tony Since you have this camera, can you verify if the lens can be replaced? It looks like it can be screwed off but I'm not sure if it's glued in or not.

So I'm working on my second quad. I am trying to build this one as cheap as possible. I have the frame, motors and a few props. I need a FC, PDB (or 4n1 ESC), camera with VTX, antenna, etc... I think I know what camera I'll use. But I may get it and swap it on my 6" quad. I have the eachine...

If this is a good one, then I'll probably get it for my quad. It will make things so simple. What are your opinions about this:

I have DLFPV 2205 2300kv motors to put on a quad. They will spinning 5045 3-bladed props. I will be using 4S 1550mAh batteries. This is the motor data for them: KV: 2300 Configuration: 12N4P Weight: 28g Ille Current(10)@10V: 0.45A No. of Cells(Lipo): 2-4S (11.1-14.8V) Max Continuous...

Test flight of the Falcon Heavy.

I recently got a good deal on some 50cal ammo cans at walmart. I thought I'd post how I did my insides. I used some scrap foam I got at work and lined the can and created some partitions. I can store 15 of these 1550mAh batteries. I used a piece of the foam to cover the battery leads so they...

Any you guys use this one before?

Went in to get a 50cal ammo can. I knew they were about $13 or so. When I got back there, they had them on rollback for $8.95. So I bought two. SCORE!

After flying, I want to put my batteries in storage. Is it bad practice to parallel storage?

I'm going to buy some motors for my foam board planes. I need to know I'm getting the correct size esc for them. I have looked at the specs but am unsure. This is the one I'm getting: US Warehouse | Eachine 2205 MN2205 2300KV 2-4S Motor For Eachine Wizard X220 X210 250 280 FPV R I'm looking...

I recently purchased the Turnigy CCPM servo consistency master gadget and upon using it on my H3050 servos, I noticed that they had some chatter whilst connected. My cheap blue 9g servos don't do this. What is the reason?

Would I get better performance from 2 blade props? I'm using 6040 3 bladed props right now. I was thinking of getting some 6040 bull nose 2 bladed ones for kicks.

HobbyTown

My goggles came with a plug that allows you to use 2 - 4S batteries to power the goggles. Can you use a cable that plugs into the XT-60 connector to power these?