Helicopters
As with the last video, this video is all about Flight Mode Settings. In this video however, you are able to fine tune your settings that you put in the gyro. Have a watch and let us know if there is anything we can help you with!
In this video, I show you how to go into the gyro and adjust the flight mode settings. There are 5 different settings in this, but some combine cyclic and collective, and others combine aileron and elevator. Watch the video below to learn how to adjust each one.
If you are out at this field...
In this video, I walk you through the rudder setup menu. If you want a stable and solid tail, then pay close attention to these steps!
I also talk about the Delay setting and how to use the software to get a perfect 0 delay setting!
I also show you how to set the Anti-Torque Compensation...
In this video, I walk you through the DIR setup mode on the gyro. In this mode, you will set all of your blade pitches including cyclic and collective. Please note, you MUST use 8º of cyclic in this step! If you require more than 8º when flying, you will make those adjustments in the Flight...
In this video, i will show you how to mount your 3GX gyro as well as how to wire it up with or without a Rx attached to it. For you 6ch guys and gals out there, you MUST use the included wires with a 6ch Rx in order to make the rudder gain adjustment work. For you 7+ channel peeps, channel 7 is...
I'm sure by now you all have read my first impressions on the RCH Heli. And to say that I was less than impressed with what we ended up with is an understatement. If you are an RCH Supporter, you know what I have went through on this heli. For those that have not read my First Impressions...
After many requests, I have decided to flash the RCH Heli's 3GX gyro to version 3.0 on the firmware. In the next videos, we will be going through the full setup of the gyro.
It's finally here, the first video in the 3GX Setup Series. In this video, I walk you through every step in the gyro setup process that you can do on the gyro its self without plugging it into the computer. This will get the gyro where you could put it in the air. But more videos are going to...
Here are the 5 most popular firmware versions for the Align 3GX Gyro. Right click, and select "Save Target As".
Align 3GX V1.2
Align 3GX V2.1
Align 3GX V3.1
Align 3GX V4.0
Align 3GX V5.0
Finally, we get the heli back to looking like a heli!
Finally, we are getting somewhere with the RCH Heli. In this video, I figure out that we are running version 1.1 on the 3GX and then I show you how to flash it to version 1.2. Yes, we are also going to run version 2.1 and version 3.0, but all in due time. As stated in teh video though, I'm sure...
It's about time we get some servos installed on this bird. Boring video, but all in building a used heli!
This is not exactly an instructional video, but more of a video showing the progress of the RCH Heli as promised to the donors of this helicopter.
In this video I go through rebuilding the head of the used Align Trex 600 Nitro Super Pro. Just because this is a larger heli, doens't mean that anything has changed. There are still thrust bearings in it as well as regular bearings and being a flybarless heli, there is a swash driver on this...
In this video, I go through rebuilding the tail on the Align T-Rex 600 Nitro Super Pro. This is oen of the most overlooked areas in a used helicopter since there are not that many parts involved. However, the few parts that are on the tail will be the deciding factor in a stable and easy to fly...
In this video, I show you everything about tearing this helicopter down. It's pretty easy, but I promised all of the donors that I would post everything I did to it. so here it is :)
Here it is, video #2 where I show you what I have right now for the helicopter. I know I was going to upload only one video a week, but this one was a lot like the last one so I decided to go ahead and upload it.
In this video you will see the helicopter, the engine, the muffler that we are...
Here is the first video in a series of the all new Rc-Help.com Helicopter. Okay, so "all new" is not the right words lol. I can't wait to get this bird in the air.
In this series, we will be doing everything from rebuilding the head, the tail, getting the servos installed, setting up the DX8...
You can view the page at http://www.rc-help.com/content.php/339-HOW-TO-Setup-helicopter-FBL-head-Align-3GX-Spektrum-by-Marius-S
I have written this many times in different threads but it always gets buried in the posts and is very hard to find. It's also one of the most asked questions here on RCH. So I thought I would do a dedicated STICKY to explain exactly how to setup correct blade pitch on a CCPM helicopter.
YOU...