Helicopters
It has been a long time coming, but lets get the AlZRC 380 motor installed as well as the Hobbywing 60 amp esc and the Ikon2 gyro mounted!
3M Double Sided Tape
https://amzn.to/2KX2tvP
Hobbywing 60 Amp ESC
https://amzn.to/2ISqstG
Ikon2 Flybarless Controller
https://amzn.to/2Du4kC9
It's time to install the servos on the Goblin 380! We already did this in a live stream, but I'm not going to make everyone sit through over 10 hours of video just to see me install some servos. We we are redoing everything on this helicopter and going step by step. let me know if you have any...
If you want to make your life just a little bit easier, use a servo tester to center your servos before you install them into your helicopter. On the Goblin 380, you can't get the arms off once you install them into the helicopter. You can do this with the gyro, but doing it this way is just a...
Here is the complete setup guide for the AR7200BX.
600/700 Feathering Shaft Wrench - http://amzn.to/2CTtvfc
450/500 Feathering Shaft Wrench - http://amzn.to/2CU5GUt
It is time to get Murphy back up in the air. But before I would feel safe flying this helicopter, we need to go completely through him and clean and lube every part of this...
This helicopter started out as the Cheapest Rc 450 Helicopter. But the further I went with it, the more I saw just how much money we were going to have to dump into it just to make it a "good" helicopter. Below are all of the links I have mentioned in all of the videos on this helicopter, as...
The Maiden Flight of the XFX 450! I was very reluctant in putting this thing in the air, but in this video, I do just that. But not without issues. So there will definitely be more videos of this helicopter.
SJCAM SJ5000X Elite - SJcam SJ5000X WIFI ELITE S ONY IMX078 GYRO 4K24 2K 2.0 Inch LCD...
This is just an overview of what I have already shown in the past on how to setup a flybar helicopter from scratch. I have already replaced the servos due to one of them being stripped out, and I have attached the gyro, Rx and battery to the helicopter as well as I put on the main blades so that...
A $60 "Super Combo" 450 helicopter? Is it worth actually purchasing? That is what this series is all about. This was the absolute cheapest helicopter kit that I would find. In this series, I will go through what this helicopter needs to get in the air and most importantly, make it SAFE...
Installing a canopy is simple, right? WRONG! Not when you move up to a Goblin. The canopy shipps with a 2mm hole already drilled into the canopy. It is up to YOU to ream that hole out to fit the 10mm (1CM for those in america lol) so that you can fit the grommets in it. Yea, I will not be doing...
It's time to add some color to this SAB Goblin 380 Helicopter! We are going to put the tail onto the frame, but not before we install the tail block onto the tail boom. I also show you how to easily install the backing blocks and get the holes lined up so you are not banging your head against...
The tail is one of the key features of the SAB Goblin Helicopter. No torque tubes here, we are running a belt on this little guy. And here is where I encounter my first issue with this kit!
In this video, I show you exactly how to assemble the rear tail block including putting together the tail...
The head on the Goblin 380 does come preassembled, but you MUST take it apart, clean all of the oil off of it and thread lock everything in place. If you are running high head speed or flying 3D, you will want to put the shims in the head which are NOT installed but are included.
In this...
The frame of the Goblin 380 has to be one of the most simple designs I have ever put together. Pair that with the simplicity of putting the mainshaft together and the gears, and this is one of the easiest helicopters to build!
In this video, we put the frame together to the lower plate, install...
It Has Begun!!!
The build of the Goblin 380 has begun. For those that do not know, this helicopter was donated to Rc-Help by Syndicate on YouTube. I have tried to get him to sign up on here, but at this time, he has not done so yet. I'm still trying lol.
This helicopter is being built by the...
Setting up a transmitter to it is ready for the Ikon 2 is quite easy. It sounds complicated, but once you do it a couple times it becomes second nature.
In this video, I walk you through, step by step, in how to setup the Spektrum DX9 Transmitter so it is ready to bind to the new Ikon 2!
Now...
In this video I show you how to install and wire the Align 450 to the Ikon 2 Gyro. The helicopter I'm using in this video is the Align 450 Pro V2 With The Align 450L Dominator Frame so I can put the gyro inside the frame. Everything about this helicopter is stock Align Pro V2 including all of...
Installing the Ikon Configurator may seem simple to some, but for those that have little to no experience with computers they may not know how, and that is what this series is going to cover.
We are starting a brand new series that is called RCH Back To Basics (#RCHBackToBasics) to get back...
After a few members told me about these servos, I hit up Jason over at Banggood to see if I could get my hands on them. He agreed and sent them to me. In the video below, I explain the servos which are already installed in my SE V2. If it could have gone wrong, it did go wrong on this video...
February 1st, 2013 was the last time the RCH Heli, AKA Murphy, the Align 600 Nitro, was put into a public video. Well today, that changes!
In this video, I catch you up on what has went on with the bird, why it has set so long and what we are planning to do with it in the future.
If you...