Helicopters
In this video, I show you how to install the Ikon Bluetooth Adapter! This is the best thing to come along since sliced bread!!!!
http://youtu.be/aKnWc6NI0K8
There are some people that just want to tinker with everything to get it "just right". I happen to be one of those people most times, but with the AR7200BX, I have to say, it's pretty solid right out of the initial setup. But for the rest of those that HAVE to have it perfect, there is the...
Since the digital pitch gauges have come out, I have noticed that some are having issues getting the pitch correctly setup on their helicopter. In this video, I show you how to properly calibrate and use a digital pitch gauge. Please post any questions, comments and/or suggestions in the...
In this video, I show you all how to go in and update your firmware on your AR7200BX. The process should be the same for the AR7300BX as well as on the original BeastX gyros.
You will need the USB link that is sold separately to update your firmware. You can purchase the USB link in the link...
This video was created by the request of a member. Once you know how to do this, and once you have your swash leveling tool, it will take you no more than 5 minutes to complete this setup. But just like pre flight inspections, this is a MUST DO after you crash or have to rebuild your servos...
It's inevitable, if you fly, you are going to crash. But unlike me, you are probably NOT going to hit the side of a house lol.
In this video, I walk you through how to rebuild the DS150 / DS155 Align servos with the MicroHeli Metal Gears from NexRc.
These are a PERFECT fit for these...
I"m sure you all have seen the DFC Linkage & Swash video where I slammed this helicopter into the side of the house. VERY HARD! This is the video where I rebuild it, and put it back into the air.
Below the video are all of the links to where you can purchase all of these parts as well as the...
Ah yeah, finally time to put some more bling on the helicopter. In this video, I put on the MicroHeli DFC Swash & Links. If you purchase this helicopter kit from NexRc...
At last, the 150 is getting it's MUCH NEEDED frame upgrade. And the flight performance after the upgrade? You will just have to watch the video to find out!
http://youtu.be/nKq_P9ThOoM
I still think the Align 150DFC is an awesome helicopter. It's as small as an MCPX, but has as much power as a 130X. And that combo is just SICK when it comes to play time!!!
In this video, I put the Black Align Main Blades as well as the Orange Align main blades against the Weighted and 3D...
I have to give a HUGE thanks to Kevin at NexRc.com for sending us this helicopter. The Align 150DFC has been known for it's issues. From tail wag, to bad boards to bad parts in general, the kickoff of this helicopter was not the greatest in the world. But these days of Chinese clones, what is...
Hello and welcome to the All New RCH Helicopter How To section! This section has taken the place of the Helpful How-To that was in the forum before. In an effort to keep the forum clean and keep the information easy to access, we have moved everything into this section.
On the left side...
We get asked this question a lot . What is the center frequency of such and so servo.
Not just helis but plane guys and quad guys need that info cause its a part of programming your gyro
So here is a very simple and extremely reliable way
-= BEASTX - BE ABSOLUTE STABLE =-
Even...
When you are building your helicopter, you take the time to install all of the servos correctly, make sure the shafts are perfect, but some over look at just how important it is to set the proper gear mesh.
If you set the mesh too loose, you run the risk of stripping the gears. If you set...
Hello everyone, The flybar head setup video is finally here. In this video, I to into more depth on the head than I do in any other video I have made. From adjusting the swash mix, to adjusting the links on the head, to leveling the swash, it's all covered in this video.
If you have any...
For over a year now, I have had requests to do a setup video on the Assan (or HK) GA-250 gyro. It wasn't until today that I was actually able to do so because I had sold all of my helicopters and the gyros went with them. Well that is over and here is the video.
In this video, I walk you...
I get 100's of people telling me there heli spun like crazy when they tried to take off.
Well with this quick check video, that should never happen again.
There are a number of things that you need to pay close attention to when building a clone helicopter. You MUST check every bolt and nut on the helicopter to make sure it's tight. You MUST put thread lock on every bolt going into metal. And if you are running a TT tail, you MUST replace the tail...
The Align DFC helicopter has gained popularity in the last year and with that comes the need to point out some things that are easily over looked.
1. Don't forget to take the head completely apart, including the arms off the grips and remove all oil that may be on the head. And let me tell...