1. If you would like to get rid of these banners and the ads within the posts, all you have to do is sign up and they will go away!
  2. Welcome to Rc-Help, are you here looking for the PDF Plans? They are located in the store in the tab above, but you must be signed in to access that part of the site. It only takes a second to sign up!
  3. Like Us On Facebook!
    Hello Guest, it occurred to us during that last server failure that we had no way of informing the members of the site of the failure and I would like to invite you to like us on facebook so that you can get updates if the site happens to go down again. We don't post much over there unless we are updating the members so we will not flood your feed like some places do. Just click on Like and then allow notifications and that's it. See you there soon!

    Click Here To Rc-Help's Facebook page!
    Dismiss Notice
Dismiss Notice
Hey Guest, I see you are not signed up on our forum yet. Did you know Registration is FREE and is only a couple clicks away? You can even sign in from Facebook, Twitter or Google+ for your convenience! So what are you waiting for, CLICK HERE to join in on the conversation!

Spektrum Ratchet On Throttle Stick

Discussion in 'Transmitters & Receivers' started by John Silva, Jan 5, 2018.

< Dx12i. Thoughts?? | Jumper T8sg Unboxing & Overview >
  1. John Silva

    John Silva New Member

    Blog Posts:
    0
    Joined:
    Dec 16, 2017
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    New Iberia, LA.
    Good morning Randy and a happy New Year:

    I want to set the throttle to ratchet on my DX8 G2 . I'm not sure what hole behind the finger pad grip to use. the video on stick adjust is not that clear as to which hole to put the screwdriver in.

    could you post a drawing of the area ?

    John
     


  2. Tony

    Tony Administrator Staff Member

    Blog Posts:
    14
    Joined:
    Feb 21, 2011
    Messages:
    35,493
    Likes Received:
    1,391
    Trophy Points:
    113
    It will be the rubber plug on the top right when you are looking at the back of the case. In the video below on changing modes, I show where this hole is and where the straps are. Hope this helps.



    PS. Who is Randy?
     
  3. John Silva

    John Silva New Member

    Blog Posts:
    0
    Joined:
    Dec 16, 2017
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    New Iberia, LA.
    My bad tony,sorry about that . In my defense i was talking to my roof installer about the same time I was writing this post

    John
     
  4. John Silva

    John Silva New Member

    Blog Posts:
    0
    Joined:
    Dec 16, 2017
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Gender:
    Male
    Location:
    New Iberia, LA.
    I HAD TO REMOVE the back of the dx8 no big deal, and found the adjustment screw to make the THROTTLE ratchet.

    Now I have what I want for THROTTLE feel

    Thanks for the assist, John
     
  5. Tony

    Tony Administrator Staff Member

    Blog Posts:
    14
    Joined:
    Feb 21, 2011
    Messages:
    35,493
    Likes Received:
    1,391
    Trophy Points:
    113
    I wouldn't think that you would have to remove the back on that Tx. Very interesting. I think I need to get my hands on one of these and do some testing.
     
< Dx12i. Thoughts?? | Jumper T8sg Unboxing & Overview >

Share This Page