450 Blade 450 X Helicopter With The Beast X - Ar7200bx

ABriscoe

Member
I have a Blade 450 X Helicopter with the Beast X - AR7200BX. What I need to know
is what should all the settings be in the Spektrum DX7s Transmitter.

In the manual that came with the helicopter it has some crazy settings that I don’t
think are for me. I don’t fly 3D so all I want is the basic setup for the transmitter.

Could you please help me with this. I have watched Tony's video on how to setup
The AR7200BX.

I attached a photo of the manual page for the transmitter settings that came with the copter and if you can tell
me what I should change for just normal flight.
Spektrum DX7s Steup.jpg
 

Tony

Staff member
What settings are you thinking are not for you? Because those settings look pretty good other than the N throttle curve. For that I would run 0 60 60 60 60 and get rid of that 30. Better when trying to lower in altitude a little quicker. Pitch curve, I run 46 48 50 75 100 in N, but with their numbers it will just give you more negative pitch to hold you on the ground which is always good.

The BX is really good at making for a soft feeling helicopter so if you set it to sport (I think), then the DR/Expo numbers look good as well.
 

ABriscoe

Member
What settings are you thinking are not for you? Because those settings look pretty good other than the N throttle curve. For that I would run 0 60 60 60 60 and get rid of that 30. Better when trying to lower in altitude a little quicker. Pitch curve, I run 46 48 50 75 100 in N, but with their numbers it will just give you more negative pitch to hold you on the ground which is always good.

The BX is really good at making for a soft feeling helicopter so if you set it to sport (I think), then the DR/Expo numbers look good as well.
Once again Tony, Your The Best... Thank You!!!!!!!!
 

Tony

Staff member
I'm not sure I understand the question. Are you talking about Menu N? Because that is just a test menu where you rotate the helicopter around and make sure the swash stays in the same orientation in space, no matter the helicopter position. But I have a feeling that is not what you are referring to.
 

ABriscoe

Member
In the Transmitter. They say that when you setup the BeastX you should use a linear curve but the photo settings that I posted they
are not linear for the transmitter.
 

Tony

Staff member
Oh, now I'm up to speed lol. You definitely want a linear pitch curve in your Tx so that mid stick is 50% pitch, low stick is full negative and high stick is full positive. Once all of that setup is done, then you will go in and set the pitch curve to what it states in the manual or what I stated before, your choice.
 

ABriscoe

Member
Oh, now I'm up to speed lol. You definitely want a linear pitch curve in your Tx so that mid stick is 50% pitch, low stick is full negative and high stick is full positive. Once all of that setup is done, then you will go in and set the pitch curve to what it states in the manual or what I stated before, your choice.
Should it just be under "N" in the transmitter or should it be all?
 

Tony

Staff member
Just N, or Normal mode. You shouldn't have to ever move your idle up, or F-Mode switch during setup.
 

Tony

Staff member
Not a pain at all bro! I'm just sorry I didn't pick up what you were putting down earlier lol. Only thing that I could think of was menu N in the BX but I knew that couldn't be right lmao. Hope you get it in the air soon!
 

Emilio Rossi

New Member
I'm trying to set up my ikon2 with my spectrum 8.Every thing is working but the throttle hold.when you flip the switch it shows that the throttle hold is working but the helicopter spoils up.all the holds are set to hold.I bound my spectrum dx6i to the helecopter and it is working fine.I'm I missing somthing.
 

Tony

Staff member
Hold the button on the roller and turn on the DX8. Scroll down to F-Mode (I think that is what it is called, don't have my Tx here with me) and make sure hold is enabled in that menu. Then, go into your throttle settings and make sure H is set to 0 all the way across.
 

Emilio Rossi

New Member
Hold the button on the roller and turn on the DX8. Scroll down to F-Mode (I think that is what it is called, don't have my Tx here with me) and make sure
Hold the button on the roller and turn on the DX8. Scroll down to F-Mode (I think that is what it is called, don't have my Tx here with me) and make sure hold is enabled in that menu. Then, go into your throttle settings and make sure H is set to 0 all the way across.
I 8
Hold the button on the roller and turn on the DX8. Scroll down to F-Mode (I think that is what it is called, don't have my Tx here with me) and make sure hold is enabled in that menu. Then, go into your throttle settings and make sure H is set to 0 all the way across.
I found the trouble that im having But don't know how to fix it.when you put the throttle hold on the slider stops but it is moving in.the wrong way.when you put the throttle all the way up the motor stops.And when you put the stick down it turns the motor on.How do I fix this.the swash moves up like it should.but something is wrong.


Hold the button on the roller and turn on the DX8. Scroll down to F-Mode (I think that is what it is called, don't have my Tx here with me) and make sure hold is enabled in that menu. Then, go into your throttle settings and make sure H is set to 0 all the way across.

hold is enabled in that menu. Then, go

Lhrottle
 
Top Bottom