RC heli Rookie
New Member
Hi, Tony. I own an E-Razor 450 and recently I purchased a DX6i transmitter. I successfully installed the AR 6115e receiver that came with the transmitter and followed the instructions on your video for "CCPM complete setup". The only problem that I could not figure out is that the tail servo is not reacting to the rudder input for both sides. The tail just spins to right but no response to the left. I tried to center the servo by connecting the servo to the rudder input in the receiver and then back into the gyro. But the problem persist. Can you help me? .Tags: None
Categories:Helicopter . Report| Promote to Article| Email Blog Entry| Unsubscribe from this Blog Entry
« Prev Main Next » Comments
Inline Mod
Select AllDeselect AllInvert Selection Select Unapproved PostsSelect Deleted Posts. Tony - 2 Days Ago 19:18 | Edit | Reply .When you connected the servo directly to the Rx, did you have full control over the servo? And what gyro are you running. i will try to keep an eye on this blog, but for future reference, you will get much more help in the forum, and not in a blog. Let me know. . RC heli Rookie - 1 Day Ago 18:24 | Edit | Reply .My apologies, it is my first time in. The gyro that I have is the GY192 and when the servo was directly connected to the Rx it was behaving in the same manner. Thank you for your patience. . Tony - 1 Day Ago 18:54 | Edit | Reply .Hm okay lets start from the beginning. What are your endpoints set at? If you have more right than left (or vice versa) set in the endpoint menu, this would do what you are describing. Let me know and we will go from there. It may be easier to set another model up and start from scratch. I have found when this is a lot more useful than tracking down one specific issue. But, lets start with the endpoints.
OH, and no worries, I"m here to help. Just wanted to let you know people usually don't look at the blog much. It's more a personal record that people keep, well Paul and I anyway lol. If I could move this out to the forum, I would, but that option is not available to me. .
RC heli Rookie - 3 Minutes Ago 22:02 | Edit | Reply .My travel adjustments are all at 100%. Pitch Curve is as follows: Normal 45% 47.5% 50% 75% and 100%, Stunt 0-25-50-75-100% Hold 25-50-75-100.
Swash Mix - all al 60%. Gyro is 0- 70% and 1- 30%.
Categories:Helicopter . Report| Promote to Article| Email Blog Entry| Unsubscribe from this Blog Entry
« Prev Main Next » Comments
Inline Mod
Select AllDeselect AllInvert Selection Select Unapproved PostsSelect Deleted Posts. Tony - 2 Days Ago 19:18 | Edit | Reply .When you connected the servo directly to the Rx, did you have full control over the servo? And what gyro are you running. i will try to keep an eye on this blog, but for future reference, you will get much more help in the forum, and not in a blog. Let me know. . RC heli Rookie - 1 Day Ago 18:24 | Edit | Reply .My apologies, it is my first time in. The gyro that I have is the GY192 and when the servo was directly connected to the Rx it was behaving in the same manner. Thank you for your patience. . Tony - 1 Day Ago 18:54 | Edit | Reply .Hm okay lets start from the beginning. What are your endpoints set at? If you have more right than left (or vice versa) set in the endpoint menu, this would do what you are describing. Let me know and we will go from there. It may be easier to set another model up and start from scratch. I have found when this is a lot more useful than tracking down one specific issue. But, lets start with the endpoints.
OH, and no worries, I"m here to help. Just wanted to let you know people usually don't look at the blog much. It's more a personal record that people keep, well Paul and I anyway lol. If I could move this out to the forum, I would, but that option is not available to me. .
RC heli Rookie - 3 Minutes Ago 22:02 | Edit | Reply .My travel adjustments are all at 100%. Pitch Curve is as follows: Normal 45% 47.5% 50% 75% and 100%, Stunt 0-25-50-75-100% Hold 25-50-75-100.
Swash Mix - all al 60%. Gyro is 0- 70% and 1- 30%.