Search results

Re: 250 quad & cc3d Yes it will. I think you need some different drivers but it'll work. - - - Updated - - - I use a small 200 dollar HP for my helis and quads running Windows 7. You can get one on Amazon.

Load cleanflight onto your cc3d's. 5v and 12v cameras and tx's, just get pdb with a step down.

I was using the CC3D when I first started flying quads. When they closed the wiki I left them and didn't look back. Right now I have 3 quads all flying SPracingF3's running betaflight and they all fly awesome. I have 2 CCD's hanging on the wall in the shop. Was going to try flashing them with...

Hey guys, anyone using these? I've been trying to set it up and I can't get it to work. I've tried 3 different firmwares, I ran the eeprom clear before loading them. I've also tried 2 different boards. One regular minumosd and one micro. Everything has power, my camera works fine without it...

Yea, I think I'm ok. I rechecked the site for the specs and it runs on 9 to 12 VoLTs.

Hey guys, picked up a Sony 600tlv super HAD board camera for my zmr250. The voltage req is 12volts. Considering I'm running 3s would it be ok to run it off the flight battery? Or would it drop out when I went under 12volts?

Just wanted to update you all on this issue. I have been flying, I have 36 flights so far but the problem has still remained. But I think I now know why it was happening. I bought a flip32 board and a orange receiver for another 250 build. I installed the orange in the 250 with the cc3d on PWM...

Yea I know. I did too but I guess it wasn't the right way. I just turned them down in the fx without any regard for the GCS. Seems like everything needs to be done through the GCS. I had my end point turned down to 125 but it didn't work. All I needed was a couple clicks but through the GCS...

I think I may have figured it out. Started over again, re flashed the board, started new in the tx. Went thru the setup and it still did it. I put everything back together and kept playing with. It seemed to work until I set up the tx. I was messing around in the manual calibration screen and I...

I can do that.

It's flashing but it's a real fast flash. I think it's slower when the other ones arm. Could it have something with the bind? I'm bound at 22ms. Should I rebind at 11ms?

Ok. Update. Now I'm really scratching my head. It's still doing it. New motors, new PDB. What am I doing wrong???? It's gotta be something simple.

I figured that but I thought I would ask. As for the screw touching anything, nope. I took them off the quad, no difference.

Tony, yea it does suck. I have a set of sunny sky motors of the same size on the way. Lee, no I didn't that but I will. As far as the sunny sky's, do you think I could mix them with emax's, or do I need to run them as a set???

Update on this problem. I received my new esc's yesterday and replaced motor 1's and it did the exact same thing. I guess in hind sight I should have switched out the esc with one of the others for trouble shooting purposes. Now it looks like I got some bad motors.

Yea. That's what I ordered too. Emaxx with SimonK.

That's my whole problem. It's the only way I can get all of the esc's to arm. Primarily 1 an 3 won't arm. Once they do it flies. Fpv is awesome. I got 4 flights in at the field and fpv'd on 2. It's great. Now I just have to get this quad to work right.

Already did. I should get them Tuesday. Strange though ain't it. I flew 3 times after the vid. What's strange too is I'll try a couple times then I'll change the throttle end point a couple clicks and try again and it'll go.

Ok. I'll change it - - - Updated - - - Ok. Works now

Ok. Here ya go. http://youtu.be/NHQUrXN8r8E - - - Updated - - - http://youtu.be/NHQUrXN8r8E - - - Updated - - - Why won't it work? Scratching my head now